********************************************************* * This firmware is for the following products: * * -------------------------------------------- * * 7700R-SC-BRC * ********************************************************* Firmware: 1.06 Build 45 Date: October 1, 2010 - Add Third Party Router support: RCP3 - Add Third Party Router support: Native SMS 7000 - Add Third Party Router support: Probel SW-P-08 - Add Third Party Router support: NEXUS Matrix 5 - Add Third Party Router support: Leitch-XY - Add Third Party Router support: RCL - Add Third Party Router support: Probel SW-P-02 - Add Third Party Control support: Probel SW-P-02 --------------------------------------------------------- Firmware: 1.04 Build 910 Date: February 12, 2010 - Add NVSP TPR (Third Party Router) support - Add NVEP TPC (Third Party Control) support - Add RCL TPC (Third Party Control) support - Add Dual Ethernet Support - Add Pro-Bel SW-P-08 TPC (Third Party Control) support. - Add GVG SMS7000 Native Protocol TPC (Third Party Control) support. - Additions made to NV9000 TPR(Third Party Router) protocol - Add Quartz "Write Name Table" support - Add ROT16 TPR - Add SH612 compatible mode -------------------------------------------------------- Firmware: 1.04 Build 55 Date: June 10th, 2009 - for third-party routers using VM/SI 3000 ASCII protocol: 1) added configurable ability to issue a crosspoint get to confirm a set 2) added configurable ability to refresh watch of all destinations - when EQX server issues a crosspoint set,7700R-SC-BRC returns 1 response set - for third-party routers using VM/SI 3000 ASCII protocol, issue crosspoint set for only those levels in which a crosspoint change would result --------------------------------------------------- Firmware: 1.04 Build 1 Date: January 26, 2009 - lock/protect infrastructe in place - lock/protect supported for third-party router protocol CPU link no. 1 - lock/protect supported for third-party router protocol NVEP - lock/protect supported for third-party control protocl CPU link no. 1 when Evertz router uses Quartz protocol - crosspoint polling corrected for NVEP-based third-party routers - further improved the speed taken to establish arouter session using the VM/SI 3000 ASCII protocol --------------------------------------------------- Firmware: 1.03 Build 35 Date: December 18, 2008 - unsolicited crosspoint update messages sent to the EQX server may now contain more than 1 level - Quartz protocol to Evertz router supports 5-figure source & destination numbers - corrected issue for third-party control of Evertz router using the Quartz protocol there was an attempt to fetch the crosspoint for the 1st (V) level even when not selected --------------------------------------------------- Firmware: 1.03 Build 29 Date: November 28, 2008 - modified the following EQX server responses: read source mnemonic: include source number read destination mnemonic: include destination number - added support for the list routes EQX server request - improved the speed taken to establish a router session using the VM/SI 3000 ASCII protocol - increase EQX server request Q size to 128 --------------------------------------------------- Firmware: 1.03 Build 12 Date: November 17, 2008 - ability to set the primary or secondary IP address of a third-party router --------------------------------------------------- Firmware: 1.03 Build 11 Date: November 11, 2008 - when interfacing to the EQX server via symphony, corrected lock-up issue when trying to set the crosspoint of a locked destination --------------------------------------------------- Firmware: 1.03 Build 10 Date: November 7, 2008 Issues Corrected: - for third-party router protocols VM/SI 3000, remote 2 (cart++), and EScontrol, bump response timeout to 1 second - fix issue whereby requests from the EQX server to control a third-party router could be dropped --------------------------------------------------- Firmware: 1.03 Build 8 Date: October 31, 2008 - the poll router mechanism will interfere less with panel/EQX server activity -------------------------------------------------- Firmware: 1.03 Build 2 Date: October 20, 2008 - add support for RE and RT EQX server requests --------------------------------------------------- Firmware: 1.03 Build 1 Date: October 17, 2008 - add support for third-party router protocol EScontrol - corrected RS-232 and RS-422 signals reversal --------------------------------------------------- Firmware: 1.02 Build 455 Date: October 8, 2008 - add support for third-party router protocol remote 2/cart++ - if communications is lost with a third-party router when the EQX server is connected, the event log may report an entry with 0.0.0.0 as the IP address of the EQX server --------------------------------------------------- Firmware: 1.02 Build 436 Date: October 3, 2008 - now sending full source and/or destination names to EQX server for names exceeding 24 characters in length --------------------------------------------------- Firmware: 1.02 Build 410 Date: September 30, 2008 - added primary level support for third-party router protocol NV9000 --------------------------------------------------- Firmware: 1.02 Build 345 Date: September 3, 2008 Issues Corrected: - in VLPro the communications status box may be red when the session status box is green --------------------------------------------------- Firmware: 1.02 Build 344 Date: September 3, 2008 New Features: - configurable Evertz router poll timer - bump default Evertz router poll timer to 45 seconds - log only Evertz router crosspoint updates indicating invalid sources/destinations when the level is applicable --------------------------------------------------- --------------------------------------------------- Firmware: 1.02 Build 341 Date: August 29, 2008 - MIB revision 4 - added third-party router source & destination offset for VM/SI 3000 ASCII protocol - added verbose event log flags - third-party control ROT16: only log crosspoint switch request --------------------------------------------------- Firmware: 1.02 Build 319 Date: August 14, 2008 Issues Corrected: - correct issue where network could become inaccessible if the EQX server doesn't properly disconnect for the purposes of third-party router control - uses virtual source/destination numbers when returning names via ROT16 protocol --------------------------------------------------- Firmware: 1.02 Build 303 Date: August 8, 2008 - add machine control router support to third- party router protocol NVEP Firmware: 1.02 Build 291 Date: August 6, 2008 - when using the Evertz router Symphony protocol, do not put an entry into the event log for unknown sources and/or destinations - when using VM/SI 3000 ASCII third-party router protocol, only put an entry into the event log indicating bad source/destination if the level is appropriate --------------------------------------------------- Firmware: 1.02 Build 281 Date: July 21, 2008 - for third-party control protocol ROT16 added the ability to transmit source and destination names after the TCP link between the 7700R-SC-BRC and the primary station is established --------------------------------------------------- Firmware: 1.02 Build 274 Date: July 21, 2008 - add support for Symphony Evertz router protocol - add support for crosspoint feedback when using EScntrl as third-party control protocol and VM/SI 3000 ASCII as third-party router protocol, this corrects the issue whereby the VM 3000 ignores unsolicited crosspoint updates --------------------------------------------------- Firmware: 1.02 Build 170 Date: July 7, 2008 - third-party control ROT16 protocol support --------------------------------------------------- --------------------------------------------------- Firmware: 1.02 Build 110 Date: June 20, 2008 - supports EQX server source and destination numbers larger than 999 --------------------------------------------------- Firmware: 1.02 Build 106 Date: June 19, 2008 New Features: - third-party control of Evertz router now has support for destination lock --------------------------------------------------- --------------------------------------------------- Firmware: 1.02 Build 74 Date: June 4, 2008 New Features: - add support for third-party router protocol NVEP --------------------------------------------------- Firmware: 1.02 Build 1 Date: May 23, 2008 New Features: - add support for third-party router protocol VM/SI 3000 ASCII - add support for third-party control protocol EScontrol --------------------------------------------------- --------------------------------------------------- Firmware: 1.01 Build 41 Date: May 13, 2008 - if the 7700R-SC-BRC receives an error rsp to a get of the first source/destination mnemonic, clear out all mnemonic names and leave the number of sources and destinations alone --------------------------------------------------- Firmware: 1.01 Build 17 Date: April 11, 2008 - configurable polling time for third-party router --------------------------------------------------- --------------------------------------------------- Firmware: 1.01 Build 9 Date: March 26, 2008 - when receiving the display switcher rsp during the session establishment process, allow the response if the number of levels appears correct and the number of configured destinations is less than or equal to the number of destinations returned in the response --------------------------------------------------- --------------------------------------------------- Firmware: 1.01 Build 8 Date: March 26, 2008 - for the third-party router task: restart the reponse timer as we receive data, a large rsp was timing out over a 9600 baud link- serial interface driver: bump the rx and tx holding areas to 256k --------------------------------------------------- Firmware: 1.01 Build 1 Date: March 24, 2008 - first firmware release --------------------------------------------------- ---------------------------------------------------